cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
419 Views
Message 11 of 19

Re: FTTC

Hi  WSH

In my previous, I was blindly assuming that an OR person would check that the DV changeover was OK at some or each of the properties, given the age of some of the folks around here.   I guess that this didn't happen in your case (!) and therefore my "declared as done" theme is irrelevant.  

Nevertheless your response was interesting. 

Endersby23

0 Ratings
Reply
391 Views
Message 12 of 19

Re: FTTC

Obviously not everyone is the same and have different levels of mobility etc , but I’d be embarrassed if as an abled bodied person I watched someone visit my home specifically to move a phone cord from one socket to another socket …I find it astonishing that some will be so entitled that they feel no embarrassment, and consider it their ‘right’ to have this done for them , a customer of Sky or Vodafone for example would get no such assistance if they were required to connect their phone to the router .

0 Ratings
Reply
239 Views
Message 13 of 19

DV Install on existing FTTC this week

Unfortunately, my diy DV Install on my long established  FTTC link earlier this week has a problem about which I'd appreciate some expert guidance. 

After following the logical published DV guidance regarding what-to-plug-where in on a Smart Hub2, outgoing phone calls then seemed to work as expected.  However, incoming calls to the home DV number never appeared at all !

I've since found that only way I can currently receive any incoming calls is to ignore the hub configuration guidance and plug a conventional PSTN telephone into the master socket.  To my surprise this delivers conventional 25Hz ringing current to the phone, a DC transmission feed on answer, and loop-disconnect dialling as well !  So is this an error at the Green FTTC PCB cabinet "around the corner"?

As to settings on my Smart Hub, it appears to think that I'm a "Full Fibre" FTTP customer and seems to resist my attempt to reset it to "FTTC".  Is this setting actually important for FTTC working? 

There seems to be very little guidance specific to DV over FTTC so can anybody give me some guidance please?

 

 

 

 

0 Ratings
Reply
234 Views
Message 14 of 19

Re: DV Install on existing FTTC this week

If your DV service has a dial-tone  ( so the phone connected to the router has a dialing tone ) call a mobile ( your own preferably ) and check the calling line identity (CLI)  displayed is correct , if it is but all incoming calls to this number still appear at the wall socket , then the migration to DV is incomplete, basically the PSTN is still delivering incoming calls, FYI , to allow the number to be moved to DV from PSTN , the PSTN service is stopped and renumbered, so 50v , dialtone and a engineering number are applied so a soft dialtone remaining at the socket is usual (for a while) even with successful migrations , you could wait and it may resolve itself in its simply delayed, or  call BT and report it .

0 Ratings
Reply
226 Views
Message 15 of 19

Re: DV Install on existing FTTC this week

All the hub setting to FTTP does is convert LAN port 4 to a WAN port for connection to the ONT.

It has absolutely no effect on FTTC connection to the DSL socket on the hub or DV.

DV on FTTC is exactly the same as DV on FTTP assuming it has been enabled correctly. 

 

0 Ratings
Reply
190 Views
Message 16 of 19

Re: DV Install on existing FTTC this week

Hi iniltous, 

Thanks for explanation about numbering migration from PSTN to DV as I'd certainly had a few "I wonder" moments  as to how it this was being tackled and didn't know that there was a delay factor in it. 

As to its impact on my (simple self install) DV over FTTC, I did report a fault because at the time, it seemed that I would be paying for a voice service that didn't allow incoming calls!   Nevertheless, the CLI checks that you suggested have shown that the situation is improving and I'll probably cancel the fault report.   

  Enderby23

0 Ratings
Reply
188 Views
Message 17 of 19

Re: DV Install on existing FTTC this week

Thanks,
As I will not need a WAN port in a FTTC situation, I'd prefer to have Port 4 as another LAN if I can successfully nudge the Smart Hub into letting me set FTTC working!
0 Ratings
Reply
186 Views
Message 18 of 19

Re: DV Install on existing FTTC this week

Thanks,
Because I don't need an ONT WAN port with FTTC working, I'd prefer to set the Smart Hub to FTTC and keep port 4 as LAN. Nevertheless my Hub "fought back" the last time I tried this!
0 Ratings
Reply
128 Views
Message 19 of 19

Re: DV Install on existing FTTC this week

There is a toggle switch for FTTP Mode under "Advanced settings" then "Broadband". 

I can't remember off the top of my head, but you may have to click "Save settings" at the top of the page after you set it.

0 Ratings
Reply