cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
1,084 Views
Message 1 of 10

DLM not lowering Noise margin

Hi All,

Quick question, I have left my router on for almost a week after going live on 1st July, I would of expected DLM to of made changes to my line, How long does it normally take for it to kick in and G.INP to activate?

Stats Below, I have achieved 73/74Meg on my line before.

Product code:Hub
 

 

Serial number:+091298+2203049317
 

 

Firmware version:v0.33.00.12274-BT
 

 

Firmware updated:Fri Jul 1 00:12:24 2022
 

 

Board version:R01
 

 

GUI version:1.74 12_11_2020
 

 

DSL uptime:6 days,12 Hours01 Mins11 Secs
 

 

Data rate:19.767 Mbps / 63.35 Mbps
 

 

Maximum data rate:19.759 Mbps / 63.501 Mbps
 

 

Full Fibre (FTTP) Mode:On
 

 

Noise margin:5.7 / 5.9
 

 

Line attenuation:9.9 / 16.2
 

 

Signal attenuation:9.9 / 18.3
 

 

VLAN id:101
 

 

Upstream error control:Off
 

 

Downstream error control:Off
 

 

Data sent / received:9.4 GB Uploaded / 74.1 GB Downloaded
 

 

Broadband username:bthomehub@btbroadband.com
 

 

Public Wi-fi status:Activated
 

 

2.4 GHz wireless network name:BT-7XCW3T
 

 

2.4 GHz wireless channel:Smart (Channel 1)
 

 

5 GHz wireless network name:BT-7XCW3T
 

 

5 GHz wireless channel:Smart (Channel 36)
 

 

Wireless security:WPA2
 

 

Wireless mode:Mode 1
 

 

Firewall:On
 

 

MAC address:18:58:80:01:92:66
 

 

Software variant:-
 

 

Boot loader:0.1.7-BT (Thu Nov 30 09:45:22 2017)
0 Ratings
Reply
9 REPLIES 9
1,064 Views
Message 2 of 10

Re: DLM not lowering Noise margin

Can take 7/10 days for DLM to activate G.INP  assuming you are on a Huawei cabinet 

In hub stats FTTP MODE should be 'off'

 



If you like a post, or want to say thanks for a helpful answer, please click on the Ratings 'Thumbs up' on left hand side.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
0 Ratings
Reply
1,063 Views
Message 3 of 10

Re: DLM not lowering Noise margin

Which exchange and cabinet are you connected to. If you are connected to an ECI cabinet, you won't benefit from either G.Inp or 3dB noise margin and are currently getting the best speed possible if that is the case.

0 Ratings
Reply
1,059 Views
Message 4 of 10

Re: DLM not lowering Noise margin

@licquorice Huawei cab. Midhurst Cab 12, Previously have had 3db in past on my old account.

@imjolly It’s now off had to sadly reboot the router ugh.. why was that on.. start again.. ugh. It’s not dropped down to 62 meg goodie! Ugh..

0 Ratings
Reply
988 Views
Message 5 of 10

Re: DLM not lowering Noise margin

Still no change? Confused would of thought it would of lowered by now..

 

Product code:Hub
 

 

Serial number:+091298+2203049317
 

 

Firmware version:v0.33.00.12274-BT
 

 

Firmware updated:Fri Jul 1 00:12:24 2022
 

 

Board version:R01
 

 

GUI version:1.74 12_11_2020
 

 

DSL uptime:12 days,07 Hours09 Mins12 Secs
 

 

Data rate:19.346 Mbps / 62.215 Mbps
 

 

Maximum data rate:19.346 Mbps / 64.247 Mbps
 

 

Full Fibre (FTTP) Mode:Off
 

 

Noise margin:6.0 / 6.4
 

 

Line attenuation:10.0 / 16.3
 

 

Signal attenuation:10.0 / 18.2
 

 

VLAN id:101
 

 

Upstream error control:Off
 

 

Downstream error control:Off
 

 

Data sent / received:13.2 GB Uploaded / 111.6 GB Downloaded
 

 

Broadband username:bthomehub@btbroadband.com
 

 

Public Wi-fi status:Activated
 

 

2.4 GHz wireless network name:BT-7XCW3T
 

 

2.4 GHz wireless channel:Smart (Channel1)
 

 

5 GHz wireless network name:BT-7XCW3T
 

 

5 GHz wireless channel:Smart (Channel36)
 

 

 
0 Ratings
Reply
978 Views
Message 6 of 10

Re: DLM not lowering Noise margin

Just checked and you are on Huawei cab.  G.INP is automatic and controlled by the DLM so there is nothing anyone can do to and you just have to stay connected and wait



If you like a post, or want to say thanks for a helpful answer, please click on the Ratings 'Thumbs up' on left hand side.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
0 Ratings
Reply
977 Views
Message 7 of 10

Re: DLM not lowering Noise margin

Thanks for checking! I will just leave it be. Its rock solid stable.. 

Thanks! 🙂

0 Ratings
Reply
904 Views
Message 8 of 10

Re: DLM not lowering Noise margin

Day 16

Product code:Hub
 

 

Serial number:+091298+2203049317
 

 

Firmware version:v0.33.00.12274-BT
 

 

Firmware updated:Fri Jul 1 00:12:24 2022
 

 

Board version:R01
 

 

GUI version:1.74 12_11_2020
 

 

DSL uptime:16 days,01 Hours29 Mins41 Secs
 

 

Data rate:19.346 Mbps / 62.215 Mbps
 

 

Maximum data rate:19.346 Mbps / 64.216 Mbps
 

 

Full Fibre (FTTP) Mode:Off
 

 

Noise margin:6.0 / 6.4
 

 

Line attenuation:10.0 / 16.3
 

 

Signal attenuation:10.0 / 18.2
 

 

VLAN id:101
 

 

Upstream error control:Off
 

 

Downstream error control:Off
 

 

Data sent / received:17.1 GB Uploaded / 147.0 GB Downloaded
 

 

Broadband username:bthomehub@btbroadband.com
 

 

Public Wi-fi status:Activated
 

 

2.4 GHz wireless network name:BT-7XCW3T
 

 

2.4 GHz wireless channel:Smart (Channel1)
 

 

5 GHz wireless network name:BT-7XCW3T
 

 

5 GHz wireless channel:Smart (Channel36)
 

 

Wireless security:WPA2
 

 

 

 

 

 

0 Ratings
Reply
896 Views
Message 9 of 10

Re: DLM not lowering Noise margin

as I posted before the application of G.INP is automatic and controlled by the DLM - there is no manual intervention



If you like a post, or want to say thanks for a helpful answer, please click on the Ratings 'Thumbs up' on left hand side.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
0 Ratings
Reply
745 Views
Message 10 of 10

Re: DLM not lowering Noise margin

Hi All,

 

I’ve left my router alone for 6 weeks and still no change? Any ideas why I’m stuck with the same speeds? I can definitely sync faster? I’ve had 74 meg on the same line back in Feb. It’s just stayed on 63 meg..

 

anyone?

0 Ratings
Reply